1 - 30FT WINDJAMMER SERIES 5000

 

Freestanding Cold Frame 168'0" long (5040 ft2)

6' bow spacing, 6' sidewall height and 16'0" peak height 

3 - runs 1.315" diameter galvanized pipe purlin per structure

58 - 2 1/4" square galvanized tube ground stakes

58 - 2" square galvanized tube half bows

13 - 1.315" round galvanized tubing cross bars, installed every other bow

Heavy-duty galvanized wind bracing provided for each end of Cold Frame structure

Certified design: This structure represents a non code design with certification un-available.

 

END WALL FRAMING

2 - Galvanized steel end wall kits complete with 2" square galv tube uprights, 2" square galv tube horizontal framing members flush mounted, as well as all necessary hardware and fasteners for 30' 0" wide frame with 6' sidewall height.

 

SIDE WALL FRAMING

2 - runs galvanized steel base board kits complete with (14) 12ft. long formed "hat" sections per run, as well as all necessary hardware and fasteners

2 - runs galvanized steel eave board kits complete with (14) 12ft. long formed "hat" sections per run, as well as all necessary hardware and fasteners   

 

2. ROOF & END WALL POLETHYLENE COVERING

1 - roll 40ft. wide x 210ft. long 6mil - 4 year CLEAR poly film sheet (to be used as inside – internal layer for roof) along with 1 - roll 40ft. wide * 210ft. long 6mil - 4 year CLEAR poly film sheet (to be used as outside - exterior layer for roof).

2 - runs galvanized steel eave board kits complete with (14) 12ft. long formed "hat" sections per run, as well as all necessary hardware and fasteners

2 - runs galvanized steel base board kits complete with (14) 12ft. long formed "hat" sections per run, as well as all necessary hardware and fasteners

2 - Galvanized steel end wall kits complete with 2" square galv tube uprights, 2" square galv tube horizontal framing members flush mounted, as well as all necessary hardware and fasteners for 30' 0" wide frame with 6ft sidewall height.

 

INFLATION KIT

1 - air inflation fan assembly complete with fresh air intake kit. 

 

CROSSOVER/JUMPER KIT

2 - air inflation crossover/jumper assemblies complete with hardware

 

ROOF POLY LOCK SYSTEM

9 - 12ft. Long sections of double track aluminum spring lock base complete with fasteners as required to secure poly at gable end bows. This assembly also doubles as a flashing for end wall 28 - 12ft. Long sections of single track aluminum spring lock base complete with fasteners as required to secure sidewall poly.

10 - 12ft. Long sections of single track aluminum spring lock base complete with fasteners as required to secure end wall poly.

112 - 6' 8" Long sections of coated spring wire for locking poly film to aluminum base profiles

 

3. END WALL COVERING Included with roof above

 

4. SIDE WALL COVERING FRESH AIR VENTS

2 - 6' high x 168' long drop down side wall curtains. Each curtain provided with outside flashing to seal the top of the curtain, aluminum spring lock base and spring insert to secure bottom of the curtain to the side wall framing girt, a manually operated 13:1 ratio gearboxes complete with hand crank extension curtain fabric (hemmed at top of assembly) curtain pipe lift tape lift pulleys

drive shaft and drive shaft hangers. Assembly also includes nylon rope and rope hangers 

 

5. DOORS

2 - 72" wide x 96" high 8mm polycarbonate single sliding doors complete with track, 8mm, door rollers, guides, door and door frame. Doors provided as an INTERIOR SLIDING assemblies,glazed with 8mm clear twin wall polycarbonate and include brush assemblies 360° around to help "seal" opening against inclement weather.

 

6. MECHANICAL VENTILATION:Neither requested or supplied

 

7. AIR CIRCULATION: Neither requested or supplied

 

8. HEATING: Neither requested or supplied

 

9. SHADE FABRIC: Neither requested or supplied

 

10. ENVIRONMENTAL CONTROLS: Neither requested or supplied

 

ESTIMATED WEIGHT: 6,932 lbs

.....................................................